ComputerHunter.org |
|
|
|||
|
 |
The Importance Of Current Sense Resistor In Switch Mode Power Supply
Current sense resistor is usually located in the switch mode power supply section. Newer version of monitor-the b+ (boost) circuit also have this current sense resistor. If you repair electronic equipment especially the switch mode power supplies, the current sensing resistor is connected to the source pin of power FET (field effect transistor) and the other end to HOT GROUND. The value of current sense resistor is in the range of 0.1 ohm to about 1 ohm. The values are depends on the design of each power supply. In monitor power supply where pulse width modulation (pwm) ic UC3842 are used. Pin 3 of this power ic is called I-sense which means current sense and this pin is connected to source pin of POWER FET. The purpose of this current sense circuit is for overcurrent protection. This circuit usually samples the voltage drop across a resistor in series with the switching fet transistor. If the current rises abnormally due to some short circuit in the secondary side such as a shorted secondary diode or horizontal output transistor (HOT), the voltage will exceed a reference level and shutdown the pulse generator which is the PWM ic. This circuit provides protection to components in the event a problem occurs. In some cases where overload happen-the power section will blow and most of the time the components changed are fuse, power fet, pwm ic, zener diode and current sense resistor. Do you know that a small change in this current sense resistor value have a great impact on the secondary output? A little change in value say from 0.22 ohm to 0.44 ohm can caused your ouput voltage to drop into half! I have seen a lot of repairer can't detect this type of problem (low output voltage) due to that they used analog or digital meter that don't have the low ohms range. You can't differentiate if the low ohms resistor has its value changed by using normal meters. I personally use the Dick Smith ESR Meter which have the capabilities to check resistor value down to 0.01 ohm! If you don't have this special meter you may just direct replace the current sense resistor to see if the generated secondary output will back to normal voltage. Another tip is that if the current sense resistor in the monitor B+ circuit have changed value it will caused the output in the boost circuit to become low and you will have a small width display and of course the high voltage will become low as well. Instead of 24Kv it becomes 15-18Kv. Jestine Yong is a electronic repairer and a writer. For more information on electronic repair please visit his website at http://www.noahtec.com/electronic-repair-articles.htm
Google News - Top Stories
|
|
|
|
RELATED ARTICLES
How To Buy A Printer That Won?t Break The Bank OK I confess I've bought at least 10 inkjet printers in the last 5 years and finally found one that I really like. I'm not going to mention the brand here but I will tell you what the must have features are for me. How to Add or Remove an IDE ROM drive CD ROMS - If you're adding or removing an internal cd-rom, dvd-rom, or just about any internal ROM that has an opening CD door, read on. Almost all IDE devices such as CD-ROM, DVD-ROM, etc. including burners and dvd burners are all installed or removed in the same fashion. If you're removing your rom, first remove the scrues from both sides of the rom. Make sure both sides are removed or you won't be able to get the device out. Once the scrues are off, unplug the drive; both the IDE ribbon cable that goes to your mainboard and your power cable. You may also have another wire running from your cd-rom to your sound card. This wire enables sound to play from your rom drive to your sound card, so when you play a cd on your drive you can hear it. Yank all cables running to the drive, then remove it. Simple. Computer Components for Idiots There are many fancy add-ons for computers, but the basic components of the computer are simple and universal. If 1 of these main components is missing, it's not a computer. Types Of Laptop Batteries Throughout the years there have been many technologies involved with notebooks, and laptop batteries are no different. There are actually three distinct notebook battery types on the market today. Knowing the difference between them will help you decide on exactly what to get when the time comes for a purchase. Expansion Cards Part 2: AGP Expansion Cards Part 2: AGP HIPPA Goes Mobile and Wireless for Hospitals and First Responders It appears we need to further streamline health care and HIPPA now in effect is quite a nightmare trying to comply with and implement without making a mistake and possibly being sued as the trial lawyers testing the law. The Malpractice insurance rates may go up again. On one hand you have the 'know your customer" laws and on the other you have "privacy rules." Rear Projection TV Facts - Understanding the Pros & Cons of Rear Projection in the Home Theater Rear Projection Television - An Affordable Option USB Key Drives - Useful Tool There are many different names for these drives, just so we are all on the same wavelength about what I'm talking about, here are a few of the other names: Printers Do you feel overwhelmed when buying a computer or a new printer? Emergency Response VSAT Internet Communications As 2005 begins, there are a number of products on the market which enable Emergency Response Units to have internet connectivity at remote disaster locations. The products marketed this year mount on vehicles from Fire Rescue units to most any type of truck or van, on specially designed trailers utilizing portable generators and in transportable boxes which can be shipped by UPS or Fed X overnight to most any location in the U.S. A response team's greatest challenge is to know enough about how this mobile satellite internet technology works and what the differences are in quality of transmission based on the equipment chosen and services provided by the Satellite Internet Provider. Pixel Disruption To Cause Nausea From User of Computer Screen As we study the issues associated with teaching kids in the classroom we find that fluorescent lighting can plague the learning abilities. A slight flicker from such a light can cause disruption in normal brain patterns. Flickering lights at discos and in psychotherapy are used for proper mood enhancement. At a disco it can loosen up a dancer and put the mind in a certain transient state allowing for the movements, mood and mind to flow in the desired pattern. For psychotherapy it can be used to put a subject in a theta state of mind to remember old memories through hypnotic states, relax a patient or even change behavior through the art of suggestion permanently by putting certain commands into the subconscious. Toner Cartridges - How They Work In the past computers and their accompanying printers were huge. Toner reservoirs and toner cartridges were used instead of ink cartridges like the ones in use today. Toner cartridges were difficult and messy to fill. The toner cartridges were an advancement. Some printers ran on print wheels and some used ribbons. How To Choose A Computer Case Things to Consider When Choosing a Computer Case Computer Parts Online In today's age, building computers on yourself is often chosen as the safest and choicest option by a sizeable part of the market for computers. There are various advantages and disadvantages for doing so. How to Avoid Getting Ripped-Off When You Purchase A New Printer It's no big secret that printer companies like HP and Brother are marketing their printers with the cost of refilling the cartridges in mind. Just the other week my family and I were at our hometown Wal-Mart and we were amazed at the price of a new printer. With joy we threw it in the cart never once thinking about the cost of refilling the contraption. War of the Disks: A Close-in Analysis of the Hard Disk Drive vs. the Solid State Disk Much has been written about solid state disks (SSDs) becoming the next big thing1 in the IT industry(1). But as to whether or not we have enough knowledge of how it will revolutionize the industry is a different question. How much do we really know about SSDs? If we are to ask people on the streets, it wouldn't come as a surprise that they dont know much of what an SSD is. Even if they do know, most probably it would be limited to a USB pen drive, a CompactFlash or a Secure Digital card, which are more on the consumer side of the storage industry. Technically speaking, they are not wrong. Most web definitions describe an SSD as a high-performance plug-and-play storage device that contains no moving parts. Therefore, given that most of the aforementioned mobile disk storage devices contain no movable parts, they can certainly be categorized as SSDs. But then again, there's more to SSDs than being a non-volatile device. The purpose of this article is to give readers a clearer picture of what an SSD is, its usage as well as its difference when pitted against the predominant data storage device at present - the hard disk drive (HDD). More than its non-volatility, this article will reveal how much potential SSDs have in optimizing the performance of the computing system. SSD Defined Here are several ways the SSD is defined: "A solid state disk (SSD) is electrically, mechanically and software compatible with a conventional (magnetic) hard disk or winchester. The difference is that the storage medium is not magnetic (like a hard disk) or optical (like a CD) but solid state semiconductor such as battery backed RAM, EPROM or other electrically erasable RAM-like chip. This provides faster access time than a disk, because the data can be randomly accessed and does not rely on a read/write interface head synchronising with a rotating disk. The SSD also provides greater physical resilience to physical vibration, shock and extreme temperature fluctuations. The only downside is a higher cost per megabyte of storage."(2) "Abbreviated SSD, a solid state disk is a high-performance plug-and-play storage device that contains no moving parts. SSD components include either DRAM or flash memory boards, a memory bus board, a CPU, and a battery card. Because they contain their own CPUs to manage data storage, they are a lot faster (18MBps for SCSI-II and 44 MBps for UltraWide SCSI interfaces) than conventional rotating hard disks ; therefore, they produce highest possible I/O rates. SSDs are most effective for server applications and server systems, where I/O response time is crucial. Data stored on SSDs should include anything that creates bottlenecks, such as databases, swap files, library and index files, and authorization and login information."(3) For the rest of the article, we will compare the HDDs and Flash-based SSDs. The latter are the most popular type of SSDs employed by the military, aerospace, industrial and embedded systems industries. Mortality Rate Hard disk failure is a common occurrence in this age of desktops and notebooks. A lot of horror stories have been told, passed around and even published about how valuable data was lost and the agony of trying to retrieve or at least save a portion of the crashed hard drive. It is during this time that people wonder, why do hard disks fail? The reason is simple - wear and tear. Just like any good old machine with mechanical components, HDDs tend to deteriorate over time. HDDs consist of rotating, magnetically coated disks, known as platters, that are used to store data. This rotating motion of the mechanical arms results in much wear and tear after long periods of use. The operational lifespan of a computer HDD is over three years.(4) A Flash-based SSD is different. Although the most common Flash chips have around 300,000 write cycles, the best Flash chips are rated at 1,000,000 write cycles per block. On top of that, Flash SSD manufacturers employ different ways to increase the longevity of the drives. In some cases, they use a "balancing" algorithm to monitor the number of times each disk block has been written, which greatly extends the operational lifespan of the drive. Furthermore, these manufacturers also designed special "wear-leveling" algorithms where once a certain percentage threshold for a given block is reached, the SSD will swap the data in that block with the data in another block that has exhibited a "read-only-like" characteristic in the background. This reduces performance lag and avoids further wearing off of the blocks and thrashing of the disk. Even with usage patterns of writing/reading gigabytes per day, a Flash-based SSD should last several years, depending on its capacity. Add to that the inclusion of a DRAM cache in the disk architecture that further enhances its operational capabilities as well as lifespan. Speeding Up With the very fast paced lifestyle these days, most businesses are time-bound and cannot afford a slowing down in their transactions. This makes speed of HDDs a crucial point in technological purchases. The typical access time for a Flash based SSD is about 35 - 100 s, whereas that of a rotating disk is around 5,000 - 10,000 s. That makes a Flash-based SSD approximately 100 times faster than a rotating disk. This however raises another point - what's the benefit of a high-speed SSD when the entire system cannot support it? The evolution of CPUs in terms of performance has far surpassed the development of the data storage system. The HDD is actually limiting the potential of a computer system when they are not able to keep up with the performance of the other components, particularly the CPU. If an HDD is replaced by a high-speed SSD, the performance would significantly improve. The resulting system would be a high-powered set-up that can go beyond the demands of high-speed business or military environments. Size Matters To be a true plug-in replacement for HDDs, Flash-based SSDs are manufactured in standard 2.5" and 3.5" form factors. 2.5" SSDs are normally used in laptops or notebooks while the 3.5" form factors are used in desktops, or in JBOD or other SAN/NAS/DAS configurations. They can often be used to replace traditional disks in storage arrays or in a server's internal disk bays. Flash-based SSDs certainly fit the storage needs of most embedded systems that require much smaller form factors. Reliability In terms of reliability, conventional HDDs pale when compared to SSDs. The absence of mechanical arms and spinning platters is the reason behind its reliability. In demanding environments, SSDs provide the type of ruggedness required for mobile applications. Unlike the HDD, SSD's can withstand extreme shock and vibration with data integrity and without any danger of data loss. This feature is very important in industrial applications where exposure to highly combustible materials and electromagnetic radiation are typical. Their ability to deliver unnerving performance in extreme conditions also makes SSD play a vital role in military operations, be it in defense, aerospace or aviation applications. Military applications require, in most cases, an operating temperature range of -60C to +95C. Shock, vibration, and temperature ratings of HDDs cannot comply with military standards, only SSDs can. Power Play In addition to speed, reliability and mortality rate being positively affected by the SSD's non-volatility, they also consume much less power than traditional HDDs. No additional power is required to activate the platters or the mechanical arms present in most HDDs. Its power consumption is practically only a fraction of a hard disk drive. Heat Dissipation Along with the lower power consumption, there is also much lesser heat dissipation for systems using Flash-based SSDs as their data storage solution. This is due to the absence of heat generated from the rotating/movable media. This certainly proves to be the one of the main advantages of Flash-based SSDs relative to that of a traditional HDD. With less heat dissipation, it serves as the ideal data storage solution for mobile systems such as PDAs, notebooks, etc. Users can do away with large cooling fans, internal power supply and batteries for large storage arrays in storage area networks. Cost Considerations Of course, everything comes with a price. Based on a cost-benefit logic, it is but expected that something with very impressive features be priced higher than something that offers fewer benefits. SSDs as being a bit more pricey than the traditional hard disk drive may be one of the compelling reasons why up to now it hasn't gained as much popularity as it should be getting with all its brilliant functions. While the use of SSDs today have mostly been limited to industrial and military implications, enterprise are now looking closely at SSDs for implementing tiered storage and optimizing their storage architectures. To quote from the Solid State Disks Buyers Guide published by storagesearch.com, "In fact the SSD is replacing servers and software licenses. SSDs can be used either to speed up the response time of existing applications as an alternative to buying more servers, or to reduce the number of servers and software licenses deployed. The economics can be compellingly in favor of an SSD deployment". The industry is also expecting more breakthroughs as higher memory capacities and faster performance are now being produced for a wider array of choices fit for any mission-critical application. Analysts foresee a rapidly closing gap between HDD and flash SSD pricing (see related article "Are Flash Solid-State Disks Ready for the Enterprise"(5) ). This vision is also bolstered by a recent announcement(6) of electronic giant Samsung that they will invest heavily in improving their flash and DRAM production lines and flash SSD equipped laptops. Only time will tell if we will witness widespread commercial adoption of SSDs.(end) This article has been reprinted from www.e-disk.com Testing Flyback Transformer - How to Test and When to Replace It Nowadays, more and more monitor comes in with flyback transformers problems. Testing flyback transformers arenot difficult if you carefully follow the instruction. In many cases, the flyback transformer can become short circuit after using not more than 2 years. This is partly due to bad design and low quality materials used during manufactures flyback transformer. The question is what kind of problems can be found in a flyback transformer and how to test and when to replace it. Here is an explanation that will help you to identify many flyback transformer problems. What Is A Fuse? And How To Test It. A fuse is a very thin wire, which either melts or vaporizes when too much current flows through it. The thin wire may be made of aluminum, tin-coated copper or nickel. The resulting open in the circuit stops current flow. In electronic equipment, most fuses are cylindrical glass or ceramic type with a metal cap at each end! The current rating also can be seen in one of the two metal end caps. There are two popular physical sizes: 1 ? X - inch and 5X20mm. The 1 ? X - inch size is used in many automobiles. You'll find both sizes in many electronic equipment, but the smaller 5 X 20mm has become more common. Fuses are available with current ratings from 1/500 Ampere to hundreds of amperes. Be Free with Wireless Speakers Are you tired of laying wires through your house, creeping through small places just to get the right sound effect? Wireless speakers are the answer to your headaches. With wireless speakers you gain the freedom to move your music to where you want it to be without the hassles of cables. Planning to have a party outside? Don't move your whole entertainment system outside while you can make use of outdoor wireless speakers which can move right along with the party. How To Choose a Computer Mouse Computer Mice
|
|
|
|
|
